865B SERIES 2

• Greater vision area.
• Comfort and ergonomics at the inside environment..

INVOLUTE BLADE

• Easy material rolling, thus increasing the earth moved volume.
• Less stress on the blade, and more fuel savings.

TRANSMISSION

• 6 speeds.
• It is coupled to the engine via torque converter.
• The converter features a locking system (Lock-up) , which transforms it in a rigid coupling, starting to work as a Direct Drive system.
• The operator can use either the automatic or manual modes.

• The hydraulic pump works in standby, consuming the minimum possible engine power, and when the application demands more flow, it is piloted for supplying the hydraulic system with the required flow, either higher or lower, depending on the operation.

SELF-ADJUSTING BRAKES

• Oil bath, multidisc, self-adjusting brakes with two circuits, one for each side of the rear axle.

MAINTENANCE

• Quick and at low cost.
• Tilting hood, which improves access to engine components and to daily maintenance points.
• Lubricating points accessible from ground level.

• Within operator’s reach and easy to operate.

RIPPER

• Rear ripper with three large teeth, in addition to five small teeth and/or five large teeth plus more nine small teeth.

SCARIFIER

• Front scarifier can have up to 11 teeth.

PLASTIC FUEL TANK

• At ground level, with lock on the lid.

TOWING BAR AND CHASSIS CIRCLE

• They provide stability, power, and maximum blade turning yield.

• ROPS/FOPS high closed cab (fixed front window) with:
  • Air conditioning (*)
  • Adjustable cloth mechanical suspension seat with 2” (50.8 mm) seat belt
  • Adjustable operator console
  • Pedal accelerator
  • Manual accelerator
  • Front upper windshield wiper with washer
  • Safety glass
  • Dome light
  • Internal and external rearview mirrors 12 V socket (*)
  • Automatic master switch
  • Steps on the right-hand and left-hand sides (*) Only available in closed cabs

All ROPS/FOPS cabs are certified according to standards SAE J1040 (ROPS) and SAE J231 (FOPS).

ENGINE

• FPT 6.7 L turbocharged, diesel,
• Tier 3 certified
• Electronic fuel injection
• Dry air filter with primary and secondary safety elements
• Air pre-filter with cyclonic dust ejector
• 90 A alternator 10,5 hp (7,8 kW) starter motor
• Swing-up hood with eletric opening and closing

HYDRAULIC SYSTEM

• Closed centre, load-sensing hydraulic system
• 9-section control valve
• Hydraulic control for all functions: blade lifting (right and left side), circle turn, circle side shift, wheel lean, chassis articulation, blade side shift and pitch, front and rear accessories
• Diagnostic centre with 8 quick couplers
• Movable saddle with 5 service positions and electro-hydraulic lock
• Blade 13’ x 2’ 2” x 0.86” (3962 x 671 x 22 mm)
• Hydraulic axial piston pump
• Hydraulic motor fan

• Multi-disk oil-bathed service brakes applied on four rear wheels, with two parallel circuits: one for right tandem wheels and another for left tandem wheels. With nitrogen accumulator safety system.
• Dry disc parking brakes, applied by spring and hydraulic release.

TYRES

• 14” Rim 3 pieces / 17,5 x 25 - 12PR - L2 Tubeless

OTHERS

• Standard tool set
• Drawbar / Standard circle

AXLES

• Conventional differential with four-wheel braking and differential lock with electro-hydraulic power drive (rear axle)

STEERING

• Hydraulic steering with built-in emergency system

INSTRUMENTS

• Electronic Information Centre
• Indicators/gauges:
  • Speedometer
  • Tachometer
  • F/N/R direction selected
  • Transmission modes – automatic/manual
  • Selected Gear
  • Engine coolant temperature
  • Fuel level
  • Transmission oil temperature
  • Hydraulic oil temperature
  • Hourmeter
• Fuel consumption
• Engine diagnostics
• DeClutch activation indicator
• Transmission diagnostics

• Low fuel level
• Flood lights
• High Beam
• Brake pressure
• Main alert
• Parking brake

AUDIBLE ALERTS

• Caution alert
• Emergency alert
• Back up alarm

ELECTRICAL SYSTEM

• Lights:
  • Front headlight with turn signal (2)
  • Brake light and rear turn signal (2)
  • Cab mounted rear flood light (2)
  • Cab mounted front flood light (2)
• 24 V system (2 x 12 V / 1010 CCA batteries)
• Electrical system monitoring
• Horn
• Hour Meter
• Back up alarm

TRANSMISSION

• ZF Transmission, torque converter type with lock up (also functions as Direct Drive), Powershift, 6 forward and 3 reverse speeds, automatic gear shifting, emergency device in case of electrical failure (Limp-Home).

REAR IMPLEMENT

Ripper with 3 large teeth and 5 small teeth 1753 lb (795 kg)

FRONT IMPLEMENT

Front counterweight 1.146 lb (520 kg)

• Cab ROPS SAE J1040
• Cab FOPS SAE J231
• Power
  • Gross SAE J1995
  • Net SAE J1349
• Torque
  • Gross SAE J1995
  • Net SAE J1349
• Brakes SAE J150/ISO-3450
• Parking Brake ISO-3450
• Steering SAE J53 / J1511
• Additional steering SAE 1011 / ISO-5010
• Turning radius ISO-7457
• Hydraulic motor turning radius SAE J499
• Engine
  • External noise SAE 1372 / ISO-6393
• Cab
  • Internal noise SAE J919

• Open cab
• Closed high cab (front flip-down window)
• Closed low cab (fixed front window)
• Closed low cab (front flip-down window)

OTHER

• Acoustic insulation for closed cab
• Fire extinguisher
• Windshield washer and lower windshield wipers
• Rear windshield washer and wipers
• Radio
• Tandem locking device
• Sun visor (front and rear)
• Rear defroster

FRONT IMPLEMENT

• Dozer blade 2568 lb (1165 kg)
• Light push plate 1084 lb (492 kg)
• Heavy push plate 1763 lb (800 kg)
• Front scarifier with 5 teeth, 6 additional teeth for front scarifier 1521 lb (690 kg)
• Dozer blade float electrovalve

• Ripper medium 3 teeth 5 scarifier
• Rear pull hook Machine lifting bracket

BLADE

• Blade 13’ x 2’ 2” x 0.86” (3962 x 671 x 22 mm)
• Blade 14’ x 2’ 2” x 0.86” (4267 x 671 x 22 mm)
• Right blade extension 2’ (610 mm)
• Left blade extension 2’ (610 mm)
• Heavy Duty cutting edge Additional

WORK LIGHTS

• 2 work lights behind the blade
• 2 service lights in front of the moldboard
• 2 rear implement work lights

LOCK/FLOATING/ANTI-SHOCK – MOLDBOARD AND CIRCLE

• Moldboard lifting cylinder lock valve
• Moldboard float electrovalve (incorporates lock valve)
• Anti-shock electrovalve with 2 accumulators for moldboard
• Anti-shock electrovalve with 3 accumulators for moldboard and circle

• Vinyl seat with mechanical suspension
• Cloth seat with air suspension
• Seat belt 3” (76,5 mm)

OTHER OPTIONAL ITEMS

• Beacon light
• Luxury tool box
• Toolbox without tools with support, fixed on front chassis
• Slow moving vehicle sign
• Electric pump to inflate tires
• Spare tire bracket
• Axles
• Conventional differential with four-wheel brake and differential lock with activation electrohydraulic (rear axle)

RIMS

• 9” rim – one-piece with valve
• 10” rim – 3-piece with valve
• 13” rim – one-piece with valve
• 14” rim – 3-piece with valve

TIRES AND RIMS MOUNTED

• Tubeless tires   - 10” rim – 3-piece / 14x24 tyre – 12L – G2   - 13” rim – one-piece / 17.5x25 tyre – 12L – L2   - 14” rim – 3-piece / 17.5x25 tyre – 12L – L2   - 14” rim – 3-piece / 17.5x25 tyre – 16L – L3
• Tube tires   - 9” rim – one-piece / 14x24 tyre – 12L – G2   - 10” rim – 3-piece / 14x24 tyre – 12L – G2
• Tubeless radial tires    - 9” rim – single-piece / 14x24 tyre – 12L – L2    - RADIAL XGLA2    - 10” rim – 3-piece / 14x24 tyre – 12L – L2    - RADIAL XGLA2