ENGINE
Model
FPT 6.7L
Type
Electronic common rail fuel system, Water cooled,4 Cycle, Direct injection, Open combustion chamber, Turbocharged, Charge air cooled. Tier IV
Cylinders
6
Bore/Stroke
4.09in x 5.17 in (104mm x 132mm)
Displacement
409 Cubic Inch (6.7 liters)
Horsepower at 2.200 rpm
Gross (SAE J1995 Gross)
Low Curve
112 kW (150 hp)
High Curve
129 kW (173 hp)
Net (SAE J1349)
Low Curve
104 kW (140 hp)
High Curve
119 kW (160 hp)
Maximum torque at 1.500 rpm
Gross (SAE J1995 Gross)
Low Curve
486 ft.lb (659 Nm)
High Curve
560 ft.lb (758 Nm)
Net (SAE J1349)
Low Curve
436 ft.lb (591 Nm)
High Curve
500 ft.lb (678 Nm)
POWERTRAIN
Rear axle
Vertical ground clearance
Differential
Tapered roller
* Brakes
Number of disks per brake
Tandem
Type
Oscillation
20° each way
Command chain pitch
2.00” pitch (50.8 mm), press fit connecting link
Thickness of the internal and external side wall
HYDRAULIC SYSTEM
Type
Piston pump, variable displacement Pressure and flow compensated, Load sensing
Hydraulic pump
Rexroth
Rated flow
49.0 GPM (186 LPM) @ 2200 RPM
Control valve
HUSCO, LOAD SENSING 9 SECTION
TRANSMISSION
Brand/Model
ZF TC LOCK UP 6WG-160
Type
Full power shift torque converter Shift modulation, downshift protection, reversals inhibited, Parking brake 15” (380 mm) dry disk, Electronic shift control mounted in R.H. console, 24V bump shifter control.
Gears
6 Forward 3 Reverse
Self-diagnostic system
Speeds - km/h
Forward/ Reverse
1st
5.2/ 4.9
2nd
3.3/ 2.0
3rd
2.1/ 0.8
4th
1.4/ -
5th
0.5/ -
6th
0.6/ -
ELECTRICAL SYSTEM
Power
24V
Alternator
BOSCH - 120A
Batteries
2x100 Ah – low maintenance
STEERING
Type
Hydrostatic power steering
Steering wheel turns (lock to lock)
4,5 turns (fast); 3,2 turns (slow)
Pump capacity
11.1 GPM (41.8 LPM) @ 2200 engine RPM
Pressure
2530 PSI (175 bar) Integral with priority valve
Cylinders
2
ARTICULATION
Type
Hydraulic actuated (with lock valve)
Angle
25° left/right
Controls
Hydraulic
CAPACITIES (REFILL)
Engine with and w/o filter
16/15 lt
Fuel DEF (urea refill)
380 lt
Transmission with and w/o filter
31/30 lt
Engine water cooling system
16 lt
Hydraulic oil tank
90 lt
Total hydraulic system
148 lt
Rear axle center
44 lt
Tandem case (each)
69 lt
SADDLE
Locking system
Two cylinders actuated by an electric solenoid. Control valve regulated by a pressure reducing valve @ 600psi (4137 kPa).
FRAME
Type
Box section
Size - Rear sectionn
254x298 mm
Size - Front section
190x327 mm
DRAWBAR
Type
“A” frame welded construction with center mounted circle turn motor. Shim adjustable at ball and circle
CIRCLE
Type
Welded construction
Maximum ouside diameter
69”(1752.6 mm)
Rotation / Speed
360°/ 1.2 RPM (7.2 degrees per second)
Nº of supports in phenolic resin
4
BLADE/MOLDBOARD
Type
Standard
Form
Involute curve
Width
358mm/ 3962mm/4267mm
Height (curved profile)
37.5” (953 mm)
Thickness
875” (22mm)
Cutting edge
2 interchangball
Blade pitch positions - Normal pitch
47°
Minimum pitch
42°
Maximum pitch
87°
Blade side shift
Right
49.5” (1257 mm)
Left
43.5” (1105 mm)
Maximum bank-cutting angle (left and right)
90°
Ground penetration (max.)
28” (711.2 mm)
Lift above ground (max.)
17.5” (444.5 mm)
Blade side shift and pitch
Hydraulic type
REAR RIPPER
Type
Parallelogram
Cutting width
85.3” (2156 mm)
Ripper teeth
5
Scarifier teeth
5/9 optional
Lift above ground - Ripper teeth
27.67” (703 mm)
Maximum penetration - Ripper teeth
12.1” (306 mm)
Weight
1410 lb (640 mm)